Sips Homes Builders

12-7~7

	Structurally Insulated Panelized System (SIPs) Foam Homes & Houses
	Structurally Insulated Panelized System (SIPs) Foam Homes & Houses.
	Building Panel Combines Foam Insulation and Steel Frame       There are two unmistakable trends in the home Building industry. First, dimensional lumber is losing its place as the dominant structural material. Second, manufactured components are steadily replacing site-built ones. Soon, panelized walls will leap to greater importance. IWe are  well-positioned for both trends.      Our panels feature 18 ga. steel tubes for strength and expanded polystyrene (EPS) foam for insulation. Wall panels are 7-1/4 in. thick (R-30) and roof panels are 11-1/2 in. thick (R-50). EPS foam is ozone-safe, because it uses air for a blowing agent, rather than CFC and HCFC compounds used by some other foam makers.      The panels are made by first routing channels for the 1x2 steel tubes. They are placed on opposite sides of the panel every 24-in. Each tube is connected to its mate with a long screw. Foam separates the opposing steel tubes, preventing thermal bridging. In the wall panel, 5-1/4 in. separates the tubes. Four steel angles placed on the top and bottom edges join the steel tubes. These angles can span the ends of adjacent panels to lock them together. Panels can be up 32 ft. long.      A 20 ga. steel angle wraps each corner, and fastens to the tubes. Siding screws directly to the tubes. Window and door openings are built into the panels and wrapped with 2x8 lumber. Roof panels sit on a ridge beam, so the entire upstairs has cathedral ceilings.        With R-30 walls and R-50 roofs made from SIPs panels, the heating load is about 25 to 30 percent of a wood-framed house, so low that a high-recovery water heater satisfies all water heating and space heating needs. A wiring chase is preformed into the wall panels and electrical boxes attach to the steel tubes. The manufacturer recommends that plumbing be located in interior partitions or in specially-built plumbing chases.        Roof Panels      Roof panels  are 4’ wide and 12” thick and up to 36’ long. They are supported by ridge and purlin (mid-span) glue laminated beams. Gable, Hip, Mansard, Arched and Flat roofs can all be constructed using roof panels.      By design all roofs are vaulted in the interior. The vaulted area can be left vaulted and showcase the expansiveness of your rooms or a floor can be constructed within to create a loft area thereby Increasing square footage of living space within the same sized envelope.      Skylights and dormers are easily Incorporated into the roofs. Exterior Walls      Exterior wall panels are 7 1/4" thick. Other thickness sizes are available specific to individual customer needs. All window and door openings, and associated headers, are built into the panels at the factory. Further, an electrical chase is factory routed into each wall panel.      In most cases it is not necessary to use exterior sheathing, however, all panels should be wrapped in the field with house wrap as a good Building practice.      Wall panels are custom made specific to each structures í architectural plans. Lengths may vary from 3" to 40' or more, and while panel heights of 8', 9', and 10' are standard, we will build wall heights of any size to suit your needs. Curved walls are also available as part of our standard panel offering.      All types of exterior finishes; aluminum siding, brick, cedar shake, metal siding, stone, stucco, vinyl or wood siding are compatible  with out  panelized wall system. Gable Panels      Typically the gable wall panels are the same thickness as the exterior walls below them. All necessary structural support for roof load beams, and any openings are Incorporated into them. For More Information Contact us at 1-928-717-9702
	Structurally Insulated Panelized System (SIPs) Foam Homes & Houses Energy Efficient Residential and Commercial SIPs Buildings Energy Efficient, Expanded PolyStyrene (EPS), Structurally Insulated Panelized System  (SIPs) Foam Homes & Commercial Buildings for sale.  PolyStyrene & Steel Framed Foam Homes; Expanded PolyStyrene EPS & SIPs Foam Houses;  Expanded PolyStyrene EPS - SIPs Steel & Foam Commercial Buildings currently available from us. Our Arizona SIPs Homes, House, and Building Manufactures located in American Arizona can provide these Expanded PolyStyrene Foam and Steel Framed Structurally Insulated Panelized System (SIPs) Buildings, homes & Houses  anywhere  within the United States for less than a conventionally priced home, house or Building would cost. Our Energy Efficient homes can be build for less than a traditional site built house, they will save you thousands in heating and cooling bills, are resistant to mildew, mold, insects, and you can be in one in less time than a traditional house. Our typical 3000 sq ft houses and houses with R-30 walls, and R-50 roof structures are designed to generally have  an approximate monthly energy HVAC Costs of somewhere around $25.00 a month for "Air Conditioning and Cooling Costs" in locations similar to American Arizona during the summers,  and of around $ 20.00 to $30,00 a month for "Heater and Heating Costs" for locations similar to those in Colorado, South Dakota, and Northern Idaho during the winters. An example of these HVAC costs; was for a home in American Arizona with approx. 3400 sq.ft. of living area that averaged less than $25 a month in heating and cooling bills over the course of a year. Similarly constructed homes, houses, and commercial Buildings benefit from the same degree of Energy Efficiency  from our product. To see to see what a typical 3,000 SQ FT   house's average monthly heating and cooling costs are like go to our Energy Ratings link. Our durable Super Strong homes have a superior survival range because our Expanded PolyStyrene SIPs Foam & Steel homes are designed to withstand winds in excess of 160 mph and to meet seismic Zone 4 requirements. Our insect and virus resistant homes are resistant to termites, carpenter ants, and dry rot ;along with being resistant to  mold  and mildew. Out homes do not outgas because our Expanded PolyStyrene EPS SIPs Foam Homes contains no CFC's or HCFC's . The homes can have a heating system that is perfect for individuals that have allergies or chemical sensitivities; you can have   an air purification system installed in your home that ensures clean, healthy air for all of the members of your family.  Our homes are pre-engineered from your blue prints in as little as three weeks from the time we receive them and your per-construction funding is in escrow. For frequently asked questions about SIPs and Expanded PolyStyrene EPS Foam Homes,  Foam Houses and EPS PolyStyrene Foam Commercial Buildings go to our SIPs -FAQ link . For more detailed and specific technical and assembly information about our SIPs and Expanded PolyStyrene EPS Foam Homes,  Foam Houses and EPS PolyStyrene Foam Commercial Buildings please see our Sips Technical Questions  link. After you have decided to purchase one of our Expanded PolyStyrene (EPS) SIPs Foam & Steel Buildings; please complete the following form and an experienced agent that is knowledgable in our Foam & Steel - Structurally Insulated Panelized Building System (SIPs) will contact you about the advantages of having a Expanded PolyStyrene SIPs home or house build for you.
	Sips Homes & Houses for sale, Expanded PolyStyrene Steel framed Buildings; Manufacturers of Sips Homes Houses & Buildings SIPs Homes, Houses and Multi Family Properties for sale SIPs Homes, Sip Houses, PolyStyrene Homes & Houses for sale Expanded PolyStyrene & Steel framed Commercial Buildings for sale Contact form Please provide the following contact information; Name Work Phone Home Phone FAX Mobile Phone E-mail How can I help you ?     All personal information is held strictly confidential. Sips Home Manufacturers In Canada. Sips Homes for sale In Canada. SIPs Buildings for sale In Canada,
	Contact us Inc. at 1-928-717-9702 for more information on SIPs Homes & Houses
	LINKS Search Engine Optimization and Free Submission